SUPREMACYIN LEAK DETECTION
Get a quoteApply now

Pool leak detection questions

From the first sign of a leak to after the repair, grouped so you can jump to yours. Anything else, call or text (945) 777-3345.

Is it a leak?

Signs, evaporation and what to do first

13 questions
How do I know my pool is leaking?

Most pools lose about a quarter inch a day to evaporation, and hot, dry, windy weather can push that toward half an inch. If you are losing more than half an inch a day, day after day, a leak is the likely cause. Skip the guesswork and book a leak detection, or run the bucket test on the Leak check page first.

What signs point to a leak?

Losing more than half an inch a day, wet or soft ground near the pool or along the pipes, cracks in the deck, the plaster or along the tile, loose tiles, air bubbles in the pump basket, algae that keeps coming back, or a water bill that keeps climbing. Any one of them is enough to book. You do not have to prove the leak first.

I have an autofill. Could the pool still be leaking?

Yes. An autofill keeps topping the pool up, so the level can look normal while water is leaving. Turn the autofill off for a day and watch the level, or check your water bill.

Why does my pool lose more water in summer?

Evaporation climbs with heat, sun, wind and dry air, so summer losses are bigger even without a leak. The evaporation checker on the Leak check page compares your loss with the weather where you live.

Do rain, splashing or backwashing throw off the numbers?

Yes. Rain raises the level, and backwashing, splash-out and a busy swim day lower it. Measure over a day without any of them, or leave those days out.

Could the leak be at the equipment instead of the pool?

Yes. Pumps, filters, valves, heaters and the unions between them all leak with age. With the pump running, look for drips, wet spots or white crust on the equipment pad, and check that water is not running out of the backwash line.

Can a slow leak wait?

It will not fix itself. You keep paying to refill and rebalance the water, and water escaping underground can wash out soil under the deck.

The water stops dropping at a certain level. What does that mean?

That level is a clue. If it stops at the bottom of the skimmer opening, look at the skimmer. If it stops at the light, it is likely the light. If it keeps falling past the skimmer and the returns, the main drain is a suspect. Tell us where it stops when you book.

How much water is my pool losing?

On a 15 by 30 foot pool, every inch is about 280 gallons. Losing half an inch a day is close to 1,000 gallons a week.

My spa drops when the pump turns off. Is that a leak?

Not always. On a spa that spills into the pool, water can drain back into the pool through the spillway or the plumbing when the pump stops. If the pool and spa together still lose more than evaporation, book a test for both.

Does a leak throw off my water chemistry?

Yes. Fresh fill water dilutes the chlorine, stabilizer and salt and shifts the pH, so a leaking pool keeps drifting out of balance and algae can keep coming back.

Can a leak damage my yard or house?

Over time, yes. Water leaving underground can wash out soil under the deck, settle pavers and coping, and soak the ground near the house. Finding it early keeps the repair small.

The pool is dropping fast. What should I do right now?

If the water falls below the skimmer opening, turn the pump off so it does not run dry. Keep people and pets away from any water pooling near the equipment or the house, then text or call us at (945) 777-3345.

Checks you can do yourself

Free tests you can run before you call

10 questions
How do I run the bucket test?

Set a bucket on the first or second step and fill it with pool water to the same level as the pool. Mark the water line inside the bucket and on the tile or skimmer, turn off the autofill, and leave both for 24 hours with no swimming or backwashing. If the pool drops more than the bucket, the extra is a leak. The full steps are in the bucket test.

What does running it with the pump on and off tell me?

Run it once with the pump running and once with it off. More loss with the pump on points to the return lines. More with it off points to the skimmer or main drain side. The same either way points to the pool shell.

Can I do a dye test myself?

Yes, for spots you can see. Turn the pump off and let the water go still, then squeeze a little leak-finding dye, or food coloring, right next to a crack, a fitting, the light or the skimmer throat. If the dye gets pulled in, water is leaving there. Buried lines cannot be dye tested from the surface. They need a pressure test.

What else can I check on my own?

Walk the yard and the path from the pool to the equipment for wet or soft spots, look along the tile line and in the skimmer throat for cracks, watch the pump basket for air bubbles, and check the equipment pad for drips while the pump runs.

Can I patch a leak myself?

A small crack you can see, like one in the skimmer throat or at the tile line, can be sealed with pool epoxy putty as a stopgap. Leaks in buried lines, the main drain or the light conduit have to be found by testing first, and patching the wrong spot only costs more water. If the patch does not stop the loss, book a leak detection.

When should I stop testing and call?

When the bucket test shows a leak, when you see wet ground or new cracks, or when the pool keeps losing more than half an inch a day. The bucket tells you that it leaks. We find where.

How do I measure how much the pool drops?

Put a piece of tape at the waterline on the tile or the skimmer and mark it. Measure from the mark 24 hours later. Turn the autofill off first, and note whether the pump ran.

How do I turn off my autofill?

Most have a shut-off valve on the water line that feeds them, often near the equipment or along the house. Close it for the test and open it again after. If you cannot find it, tell us when you book.

What should I photograph before I book?

The equipment pad, any wet spots, cracks, the skimmer, the tile line and your waterline mark. Send them with your booking text so we come prepared.

Is it safe to look for the leak myself?

Looking from the deck is fine. Stay away from the main drain and open fittings while the pump is running, keep children and pets away from the equipment, and leave anything electrical to a licensed pro.

Before your visit

Booking and getting the pool ready

15 questions
How do I book?

Book online in about a minute and your booking comes to us as a text, or text or call (945) 777-3345. We confirm the time by text and by email.

Can I send photos, videos or an old leak report?

Yes, please. Add them when you book, or text them to (945) 777-3345. Photos of the pool, the equipment pad and any wet spots, a short video, your water bill or an old leak report help the tech come prepared.

How will I know my booking went through?

We confirm every booking by text and by email, with the day and the time. If you do not hear from us, call or text (945) 777-3345.

How soon can you come?

The same day when we can. Pick the day that works for you when you book, and we confirm it by text.

What should I tell you when I book?

How many pools and spas you have, every water feature (bubblers, waterfalls, deck jets, scuppers), extra pumps, in-floor cleaning, how much the pool drops a day, and anything you have seen. Photos or a short video help us come prepared.

What should I do before the visit?

Get the water clear, with no algae and no cloudiness, and fill the pool to its normal level, about the middle of the skimmer opening. Top it off a few hours ahead and run the pump. Skim and vacuum, and make sure we can get through the gate and to the equipment. The full list is in Get the pool ready.

What if my pool is cloudy or green?

Get it clear before we come. We need clear water with no algae to do the leak detection. If it is still cloudy when we arrive, we can run some tests, like pressure testing the lines, but we cannot dive, and anything that needs a dive waits until the water clears.

Should I drain the pool or let it drop?

No. Keep it at its normal level, about the middle of the skimmer opening. If the pool drops to the leak, nothing pushes water out of it and it cannot be heard, and emptying a pool can damage it.

Do I need to be home?

No. Make sure we can get through the gate and to the equipment. Everybody gets a report with pictures and videos of what we found, whether you are home or not.

Should the pump be running when you arrive?

Yes. Run the pump and filter, and top the pool off a few hours ahead. The equipment has to run so we can test it.

Do I need to clean the pool first?

Skim and vacuum so the floor, steps and fittings are clear. Debris can plug a leak and hide it.

Can you test a pool at a house I am buying or selling?

Yes. Pick Home buyer or realtor when you book and tell us who should get the report, like the buyer and both agents.

I run a pool service company. Can I send you a job?

Yes. Send us the address and what your customer is seeing, and tell us who gets the report.

We are replastering or remodeling. Should we test first?

Yes. A leak check before a replaster or remodel makes sure the new finish goes on a pool that holds water.

Can I change my appointment?

Yes. Text us and we will find a new time.

During the visit

How we test and what to expect

12 questions
How do you find the leak?

We pressure test the plumbing lines one at a time, dye test the fittings, the light, the skimmer and any cracks, and inspect underwater where it is needed. The line that will not hold pressure, or the spot that pulls dye, is the leak.

What tools do you use?

Pressure testing, dye testing, underwater listening, a pipe camera, line locating and, for hard-to-find underground leaks, tracer gas. Which ones come out depends on the pool. Our technicians are certified on Anderson and LeakTronics equipment.

Do you get in the pool?

When the water is clear enough to see the main drain, yes. We dive to check the shell, the light and the fittings up close. We cannot dive in water that is not clear.

What if the water is cold?

Above 70°F there is no dive fee. Between 55 and 70°F a cold water dive adds $99. Below 55°F we run the other tests and dive once the water warms up. The price builder estimates the water from the air temperature at your ZIP, and we measure it when we arrive.

Do you check spas and water features?

Yes. Attached spas and water features are tested the same way as the pool.

Will you dig up my yard or deck?

Only where the testing points, and only after you approve the repair price. A line locator traces the pipe first, so we open the smallest spot we can.

How long does it take?

It depends on the pool. Every line gets tested, so a pool with a spa, water features and extra pumps takes longer than a simple pool. We tell you what to expect when we confirm.

Who comes out?

A background-checked technician certified on Anderson and LeakTronics leak detection equipment.

Can we swim while you test?

Not while we are testing. The water has to be still for dye testing and listening.

Do you test the equipment pad?

Yes. We check the pump, filter, heater, valves and unions for leaks while we are there.

Do you check the main drain?

Yes. The main drain line is pressure tested with the others, and we check the drain and its cover when we dive.

Can I watch you work?

Yes, if you are home. The technician can show you what we find as we go, and the report has it all either way.

After the visit

Your report, the repair and what comes next

10 questions
What do I get afterward?

A report with pictures and videos of what we tested and what we found, whether you were home or not, plus the repair price for anything we could not stop on the spot.

Do you stop the leak on the same visit?

When the leak is easy to reach and a quick stop makes sense, yes, at no extra cost. We close a diverter valve when that stops a leaking line, seal a skimmer throat with epoxy putty, and seal a light conduit with butyl tape and putty. Capping an underground line is a repair, priced before any work starts. Bigger repairs are priced before any work starts.

What if you do not find a leak?

Then you know the loss is evaporation or something outside the pool, like the autofill, splash-out or backwashing, and you can stop worrying about a leak. The price is the same either way, because every line still gets tested.

How soon can you do the repair?

Simple leak stops happen on the same visit. Bigger repairs are priced first, and we set a time once you approve.

Do you test again after the repair?

Yes. After we repair a line, we pressure test it again before we close it up.

Can I share the report?

Yes. It is yours to send to your insurance company, your HOA, a buyer or another contractor.

What should I watch for after the repair?

Keep an eye on the water level for a few days. If it still drops faster than evaporation, text us. The repair is under warranty.

Will you explain what you found?

Yes. If you are home, the technician walks you through it. If not, the report shows each finding with photos and video, and you can text us your questions.

What if there is more than one leak?

It happens. Every line is tested, so the report lists each leak we find and the price to fix each one.

Can my own pool company do the repair?

Yes. The report shows where the leak is, so you can hand it to any qualified company. If we do the repair, it carries our 2 to 10 year warranty.

Prices

What it costs and what adds to it

8 questions
What does leak detection cost?

Pool or spa leak detection is $550. Pool and spa together is $650. In the Austin area it is $700 for a pool or spa and $800 for both. Fountains and water slides are included. Bubblers, waterfalls and other water features are $99 each on top. Extra pumps are $99 each, an in-floor cleaning system starts at $400, and a cold water dive is $99. We confirm your final price before we start. If a repair is needed, you get that price before any work starts.

Can the price change on the day?

Only if the pool is different from what was booked: more water features, pumps or in-floor cleaning heads than listed, or water cold enough for a dive fee. We check when we arrive and tell you the price before we start.

Why a flat price?

So you know the cost before we come, and it does not go up if the leak is hard to find. Every extra is listed up front in the price builder.

Is it more outside Dallas–Fort Worth?

Only in the Austin area: $700 for a pool or spa and $800 for both. Houston, San Antonio, Weatherford and Texarkana pay the DFW price.

Why do water features cost extra?

Each one has its own plumbing to test. Fountains and water slides are included. Bubblers, waterfalls, deck jets, scuppers and the like are $99 each.

What do extra pumps add?

$99 for every pump beyond the first, since each runs its own lines. Booster pumps do not count.

What does in-floor cleaning add?

It starts at $400, which covers up to 20 heads, then $20 for each head over 20.

Is an infinity edge extra?

The catch basin and its lines are $99, tested along with the pool.

Choosing a leak detection company

What to ask and what to watch for

10 questions
What should I ask a leak detection company?

Do they pressure test every line, or only look? Do they get in the pool? Will you get a report with photos and video? Is the price flat or by the hour? Do they repair what they find, and with what warranty? Are they licensed and insured?

How do I check a license in Texas?

Ask for the license number and look it up on the Texas Department of Licensing and Regulation website. Ours is RAIC #1505.

Are you licensed and insured?

Yes. We hold TDLR appliance installation contractor license RAIC #1505 and a RAIL license, our owner is a PHTA Certified Building Professional and Certified Pool Inspector, and we are insured. We are veteran-owned and BBB accredited.

Do certifications matter?

Leak detection tools take training to read right. Anderson and LeakTronics make leak detection equipment and certify technicians on it. Ours are certified on both.

Why pick a company that also repairs?

You are not left holding a report and hunting for a second company. The people who found the leak fix it, and the repair carries a 2 to 10 year warranty.

What are the red flags?

Being told to drain the pool before any testing, parts replaced one by one to see if the loss stops, no written report, and an hourly rate with no limit.

What do your customers say?

We are rated 5.0 on Google with more than 300 reviews, and more than 10,000 DFW homeowners have used us since 2013. When you compare companies, read the recent reviews that mention leak detection, not only pool cleaning.

Should a leak detection company get in the pool?

Some leaks only show up close: at the light, a fitting or a crack below the waterline. A company that never gets in can miss them.

Is the cheapest leak detection the best deal?

Not if it ends in a second visit or a repair in the wrong place. Compare what is included: every line pressure tested, a dive, a photo and video report, and simple leak stops.

Is one kind of test enough?

Not always. Pressure, dye, listening and cameras each find different leaks, so a good company picks the tools for the pool instead of running one test and guessing.

Repairs

What we fix and how

8 questions
Do you repair the leak too?

Yes. We find it and we fix it: skimmers, return fittings, lights, main drains, underground pipes, cracks and equipment.

Is the work under warranty?

Yes. All our work carries a warranty of at least 2 years, and up to 10 years depending on the repair.

Where can I read more about repairs?

The Pool repair page covers skimmers, return fittings, lights, drains, underground pipes, cracks and equipment, with more repair questions.

Can you fix a cracked skimmer?

Yes. Cracked skimmer throats and separated seams can be sealed. A skimmer that is broken through gets replaced and the deck patched.

Can you fix a leaking pool light?

Yes. We seal leaks around the light niche and up the conduit, then reset the light.

Do you repair underground pipes?

Yes. We dig only where the pressure test points, replace the broken section and pressure test it again.

Can cracks in the plaster be sealed?

Yes. Cracks in the plaster, at the tile line and on the steps can be sealed so they stop pulling water.

Do you repair spas and water features?

Yes. Spas, waterfalls, fountains and scuppers are tested and repaired like the pool.

Commercial pools

HOAs, apartments, hotels, cities, schools and builders

10 questions
How do you price a commercial pool?

A commercial pool up to 30,000 gallons with no more than 2 skimmers, 6 returns and 2 main drains is our flat price: $550 for a pool or spa and $650 for both, or $700 and $800 in the Austin area. Anything bigger gets a custom quote. Send the property, the gallons, the skimmers, returns and main drains, and photos or plans if you have them, and our team sends you the price before anything is booked.

Do you work on commercial pools?

Yes. HOAs, apartments, hotels, cities and parks, clubs, schools and gyms. We have worked for Hilton, Marriott and AC Hotel properties, Greystar apartment communities in Dallas and Houston, the City of Sachse, rooftop pools in Dallas, and neighborhood pools in The Fields and Craig Ranch. Pools up to 30,000 gallons with no more than 2 skimmers, 6 returns and 2 main drains are the same flat price as homes. Bigger pools, and properties with more than one pool or spa, get a custom quote before we come out. Ask for a commercial quote.

Can you work around our pool hours?

Yes. Tell us the pool hours when you ask for a quote, and we plan the testing to keep closures short. Your board or manager gets the photo and video report.

Can you test several pools at one property?

Yes. Tell us how many pools, spas and splash pads you have, and we confirm one total for the property before we come out.

Will the report work for our board or city?

Yes. It shows each finding with photos and video, so managers, boards and city staff can see the problem before they approve the repair.

Do you test splash pads and water features?

Yes. Slides, spray pads and features have their own lines and tanks, and we test them like the pool.

We manage several properties. Can you handle all of them?

Yes. One contact and one schedule for every pool.

We remodeled a pool and the owner says it never leaked before. Can you help?

Yes. A post-remodel leak check tests every line, the fittings and the shell, and the photo and video report shows where the water is going, so everyone can see whether it has anything to do with the work.

Can you check a new pool before we hand it over?

Yes. A post-construction leak check tests every line, the fittings and the shell before the owner takes over, and you keep the photo and video report.

Why are commercial leaks harder to find?

Bigger plumbing, more returns and drains, and surge or balance tanks and autofills that can hide water loss for weeks.

Service area

Where we come, and the price there

3 questions
Which areas do you cover?

Every city in Dallas–Fort Worth, including Dallas, Fort Worth, Frisco, Plano, McKinney, Allen, Arlington, Irving and Denton. Outside DFW we also come to Austin, San Antonio, Houston, Weatherford and Texarkana. Not sure about your address? Text us your ZIP.

Do you cover my neighborhood?

Search your city, neighborhood or ZIP on the Areas page map, or text us your ZIP.

How far outside DFW do you go?

Across Texas, out to the Oklahoma and Louisiana borders, with Austin, San Antonio, Houston, Weatherford and Texarkana on our map. Text us your ZIP if you are not sure.

About us

Who we are

7 questions
How long have you been doing this?

Since 2013. More than 10,000 DFW homeowners have used us.

Who owns Supremacy in Leak Detection?

We are veteran-owned, and part of Supremacy Service, a home service company serving Dallas–Fort Worth.

Where are you based?

Lewisville, Texas, north of Dallas.

Is leak detection all you do?

Swimming pool and spa leak detection, and the repairs that follow, are the whole job here.

Are you hiring?

Yes. We are looking for leak detection technicians and repair technicians. See Careers.

What do you guarantee?

Ten things, on every visit: a flat price, every line tested, a photo and video report, the repair price before any work, simple stops included, a 2 to 10 year warranty, a certified technician, on time or $50 off, a free retest within 30 days of our repair, and a clean site: we treat your home like our own. See our guarantees.

How do I reach you?

Call or text (945) 777-3345, or email get@supremacyservice.com.

Stop refilling the pool.

Book in about a minute. We confirm your visit by text and email.

Get a quoteApply now Text Call